POSSIBLE MEASURES TO EXTEND THE SERVICE LIFE OF DIESEL FUEL PUMP MAIN COMPONENTS
DOI 10.12737/2073-0462-2023-72-76 УДК 621.43.031
Keywords:
fuel injection pump, hydrocar bon fuel, mechanical impurities, wear r ate, precision element.Abstract
During the operation of a high-pressure fuel injection pump, the friction surfaces of the main elements are subjected to various mechanical, thermophysical and hydroabrasive effects, which increases the wear rate of precision elements and reduces the cyclic fuel supply through the cylinders. The purpose of the research is to increase the resource of the main elements of in-line high-pressure fuel pumps by modernizing the power supply system. The main factor affecting the performance of precision elements is the presence of carbovalt in hydrocarbon fuel, that is, mechanical impurities in the form of an abrasive that circulate throughout the entire circuit of the power supply system, can pass through the filter element and get into the junction of precision elements during the injection cycle, where they are pinched and abraded work surfaces. In addition to mechanical impurities, hydrocarbon fuels may contain surfactants such as sulfur, phosphorus, etc. Under certain conditions, this also accelerates the wear rate of friction pairs, especially at temperatures above 50°C. With an increase in temperature, the lubricity of hydrocarbon fuels decreases, since sulfur compounds are activated, which destroy the structured surface at the boundary of friction pairs. To reduce this effect, it is proposed to limit the increase in temperature in the diesel power system by installing a radiator with a fan. With temperature limitation in the diesel fuel system, the wear intensity will be lower, the viscosity will be consistently higher by 2 times or more, which will reduce fuel leakage in mating surfaces. The above analytical expressions indicate that the size of the fuel leakage depends on the Reynolds number. With an increase in viscosity, the Reynolds number decreases several times, while the consumption coefficient and fuel leakage through the gaps of the friction pairs are significantly reduced. The proposed measure makes it possible to preserve the lubricity of the fuel, reducing wear and increasing the service life of the main elements of the fuel injection pump.
References
1. Габдрафиков Ф.З., Шарифуллин Ф.А. Повышение эффективности работы дизеля интенсификацией впрыскивания топлива // Механизация и электрификация сельского хозяйства 2013.№ 5.С.30-31.
2. Минимизация утечек топлива в изношенных плунжерных парах смещением зон износа / В. Н. Гаврилов, А. М. Новиков, А. В. Семенов и др.// Вестник Казанского государственного аграрного университета. 2019. Т. 14. № 4-2(56). С. 49-53.
3. Прогнозная оценка возможных значений давления впрыска топлива системы common rail / В. А. Иванов, А. В. Семенов, В. Н. Гаврилов и др. // Вестник Казанского государственного аграрного университета. 2020. Т. 15. № 2 (58). С. 92-95.
4. Казаков Ю. Ф.,Иванов В. А. Аналитическая оценка технического состояния плунжерных пар при комплектации их по гидроплотности // Вестник Казанского ГАУ. 2018. № 1 (48). С.138-142.
5. Астахов И. В. Топливные системы и экономичность дизелей / И.В. Астахов, Л. Н. Голубков, В. И.Трусов и др. М.: Машиностроение, 1990. 287 с.
6. Голубков Л.Н., Савастенко А.А., Эмиль М.В. Топливные насосы высокого давления распределительного типа BosсhVe, Лукас, Зексель, Ротодизель, НД. М.: Легион-Автодата, 2016. 184 с.
7. Надежность и ремонт машин / под ред. В.В. Курчаткина. М.: Колос, 2000. 776 с.
8. Eriksson L., Nielsen L. Modeling and Control of Engines and Drivelines. John Wiley Sons, 2014. P. 107-110.
9. Salykin E.A., Lipilin V.I., Skorobogatov A.A. Method of Fuel Injection in Small Diesel EnginesAuthorlinks open overlay panel // Procedia Engineering. 2017. Vol. 206. P. 1552-1557.
10. M.S. Stavljanin. Mathematical modeling and identification of the mathematical model parameters of diesel fuel injection systems // Vojnotehnicki glasnik. 2017. Vol. 65. No. 2. P. 421-441.
11. Гидравлика, гидромашины и гидропиводы / под ред. Т.М. Башта, С.С. Руднева, Б.Б. Некрасова, 2-е изд., перераб. М.: Машиностроение, 1982. 424 с.
12. Галиев, И. Г. Модернизация смазочной системы подшипника турбокомпрессора дизельного двигателя / И. Г. Галиев, Е. П. Парлюк, Б. Г. Зиганшин // Вестник Казанского государственного аграрного университета. – 2021. – Т. 16, № 3(63). – С. 67-71. – DOI 10.12737/2073-0462-2021-67-71.
1. Gabdrafikov FZ, Sharifullin FA. [Improving the efficiency of a diesel engine by intensifying fuel injection]. Mekhanizatsiya i elektrifikatsiya sel'skogo khozyaistva 2013; 5. 30-31 p.
2. Gavrilov VN, Novikov AM, Semenov AV. [Minimization of fuel leaks in worn plunger pairs by displacement of wear zones]. Vestnik Kazanskogo gosudarstvennogo agrarnogo universiteta. 2019; Vol.14. 4-2(56). 49-53 p.
3. Ivanov VA, Semenov AV, Gavrilov VN. [Predictive assessment of possible values of common rail fuel injection pressure]. Vestnik Kazanskogo gosudarstvennogo agrarnogo universiteta. 2020; Vol.15. 2(58). 92-95 p.
4. Kazakov YuF, Ivanov VA. [Analytical assessment of the technical condition of plunger pairs when they are assembled according to hydraulic density]. Vestnik Kazanskogo GAU. 2018; 1 (48). 138-142 p.
5. Astakhov IV, Golubkov LN, Trusov VI. Toplivnye sistemy i ekonomichnost' dizeley. [Fuel systems and efficiency of diesel engines]. Moscow: Mashinostroenie. 1990; 287 p.
6. Golubkov LN, Savastenko AA, Emil' MV. Toplivnye nasosy vysokogo davleniya raspredelitel'nogo tipa BosshVe, Lukas, Zeksel', Rotodizel', ND. [Fuel pumps of a high pressure of the distributive type BoschVe, Lukas, Zeksel, Rotodizel, ND]. Moscow: Legion-Avtodata. 2016; 184 p.
7. Kurchatkin VV. Nadezhnost' i remont mashin. [Reliability and repair of machines]. Moscow: Kolos. 2000; 776 p.
8. Eriksson L, Nielsen L. Modeling and control of engines and drivelines. John Wiley Sons. 2014; 107-110 p.
9. Salykin EA, Lipilin VI, Skorobogatov AA. Method of fuel injection in small diesel engines authorlinks open overlay panel. Procedia engineering. 2017; Vol.206. 1552-1557 p.
10. Stavljanin MS. [Mathematical modeling and identification of the mathematical model parameters of diesel fuel injection systems]. Vojnotehnicki glasnik. 2017; Vol.65. 2. 421-441 p.
11. Bashta TM, Rudnev SS, Nekrasov BB. Gidravlika, gidromashiny i gidropivody. [Hydraulics, hydraulic machines and hydraulic actuators]. Moscow: Mashinostroenie. 1982; 424 p.
12. Galiev IG, Parlyuk EP, Ziganshin BG. [Modernization of the lubrication system of the turbocharger bearing of a diesel engine]. Vestnik Kazanskogo gosudarstvennogo agrarnogo universiteta. 2021; Vol. 16. 3(63). 67-71 p. – DOI 10.12737/2073-0462-2021-67-71.
Downloads
Published
How to Cite
Issue
Section
Categories
License
Copyright (c) 2026 Vestnik of Kazan state agrarian university
This work is licensed under a Creative Commons Attribution 4.0 International License.
Метаданные научных статей, включая название, аннотацию, сведения об авторах, список литературы, идентификаторы и иные элементы библиографического описания для дальнейшего неограниченного использования, передаются в редакцию с правом их неограниченного использования на условиях открытой лицензии Creative Commons Attribution (CC BY).
